Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Grades Titanium Alloys Mechanical Chemical Physical Properties Ti 6-2-4-2 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Ti 15-3-3-3 Titanium 6Al4V IMI 685 Titanium Alloys Mechanical Chemical Physical Properties IMI 829 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 Grade 5 / ELI / 23 Grade 9 / 18 Grade 19 / 20 titanioum , titan, titane, titanio, tianium, titaium, titanim, titaniom, titanium, titanum, titnium, ttanium, t1tan1um, titanium, titamium, titanimu, titanuim, titainum, titnaium, tiatnium, ttianium, ittanium, titaniu, titanim, titanum, titaium, titnium, tianium, ttanium, itanium, titaniom

- about Ti - Introduction Ind. Specification Medical Specification Applications Characteristics Classification Markets Corrosion Engineering Fabrication   - Ti Grades - Introduction Ti 6-2-4-2 Ti 15-3-3-3 Ti 13Nb-13Zr IMI 685 IMI 829 SMA CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 6Al4V Grade 5 / 23 6Al7Nb Alloy Grade 9 / 18 Alloy Grade 19 / 20   - Ti Products - Introduction Fine Wire - Cable Foil Sheet / Plate Titanium Targets Tube Oilfield Tubes

» Titanium Alloy Ti-13Nb-13Zr ASTM F1713

Wrought Titanium 13 Niobium - 13 Zirconium Alloy for Surgical Implant Applications (UNSR58130)

3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 beta transus, n—the minimum temperature at which the alpha plus beta phase can transform to 100 % beta phase.
3.1.2 capability-aged, adj—the condition of the material that is obtained if, following solution treatment, a sample of the mill product is subjected to an aging treatment such as given below, for certification testing.
3.1.2.1 Age for 6 6 0.25 h at 923 6 25°F (495 6 14°C).
3.1.2.2 Remove from furnace and air cool to room temperature.
3.1.3 cold work, n—any mechanical deformation process performed below the recrystallization temperature which results in strain hardening of the material.
3.1.4 hot work, n—any mechanical deformation process performed above the recrystallization temperature.
3.1.5 lot, n—the total number of mill products produced from the same melt heat under the same conditions at essentially the same time.
3.1.6 solution-treated, adj—the condition of the material that is obtained if, following the final hot-working or cold-working operation, the mill product is rapidly quenched, for example, by water quenching, from a temperature above 1112°F (600°C).
3.1.7 unannealed, adj—the condition of the material that is obtained after the normal hot-working or cold-working operation used for fabrication of the mill product. There are no subsequent heat treatment requirements.

Composition Physical Data Mechanical Data Fabrication Information

» Composition

C	< 0.08 %
Fe	< 0.25 %
N2	< 0.05 %
O2	< 0.15 %
H2	< 0.012 %
Nb	12.5 - 14 %
Zr	12.5 - 14 %
Ti =	Rem

» Physical Data

Minimum

Typical

» Mechanical Data

	Capability aged	Solution treated	Unannealed
Tensile Strength MPa(ksi)	860 (125)	550 (80)	550 (80)
0.2% Proof Stress MPa(ksi)	725 (105)	345 (50)	345 (50)
Elongation over 2 Inches %	8	15	8
Reduction in Area %	15	30	15

» Fabrication Information

Titanium Tantalum Molybdenum Niobium Zirconium Tungsten
Tel CH: +41 444 6353 82 Tel DE: +49 7424 9699616
REACH, RoHS compliant - Conflict Free Materials © 1994-2023 Titanex GmbH Switzerland
 

Titanium 6Al4V

Titanium Alloys Mechanical Chemical Physical Properties

Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V